Quote request · Outdoor Kitchens

Outdoor Kitchen Builder

Lay out a steel or aluminum outdoor kitchen step by step: layout, cladding, countertop and appliance cut-outs, with a live plan and elevation. MS Metals fabricates the metal frame and cabinetry and can help coordinate with other contractors for countertops, plumbing, electrical and appliances. We review your spec and follow up with a quote.

Step 1 of 9

Layout

MS Metals fabricates the metal frame and cabinetry and can help coordinate with other contractors for countertops, plumbing, electrical and appliances.

Kitchen layout *

Straight / linearOne run along a wall or fenceL-shapeMain run + one returnU-shapeMain run + two returnsIslandFreestanding, open on all sidesPeninsula / barReturn with a bar side for seating

Back side

Step 2 of 9

Dimensions

Approximate numbers are fine; we confirm everything on site and on the shop drawings.

Main run length * (ft)

Return length (left side for U-shape) * (ft)

Right return length * (ft)

Counter depth * (in)

Typical: 30" for a run, 36"–42" for an island.

Counter height * (in)

Standard kitchen counter height is 36".

Raised bar ledge

A raised counter on the seating side.

Bar ledge height (in)

Bar ledge depth / overhang (in)

Cabinet space used by cut-outs

90" of about 180" usable (excluding corners)

Step 3 of 9

Frame material

Frame material *

SteelVery rigid; galvanize for South Florida.AluminumLightweight, no rust, low maintenance. Recommended for coastal sites.

Coastal site? We recommend aluminum (or 316 stainless steel) for salt-air exposure.

Hot-dip galvanize (recommended for steel; done before any powder coat)

Step 4 of 9

Cladding & finish

Exterior cladding / finish *

BlackWhiteBronzeCustom color (RAL)Mill finish (no powder coat)Stainless steel panelsWood-grain lookCustomer supplies stone / tile veneer

RAL color code

Texture

SmoothTextured

Stainless grade

Doors & drawer fronts

Step 5 of 9

Countertop

Countertop *

Customer-suppliedYou provide itGraniteBy others, coordinatedQuartzBy others, coordinatedConcreteBy others, coordinatedStainless steelBy others, coordinatedNot sure yetHelp me decide

MS Metals fabricates the metal frame and cabinetry and can help coordinate with other contractors for countertops, plumbing, electrical and appliances. Countertops are supplied and installed by others; tell us your preferred material and we build the frame to suit it.

Countertop overhang past the cabinet face (in)

Step 6 of 9

Appliances & cut-outs

Choose the bays and cut-outs to build into the frame. MS Metals builds the bays and cut-outs; appliances are supplied and installed by others, and we can help coordinate with your appliance contractor. Send model numbers if you have them so cut-outs match the spec sheets.

Built-in grill

Grill width

30"36"42"48"Other / not sure

Side burner

Side burner type

Sink

Outdoor refrigerator (under-counter)

Ice maker or ice bin

Ice

Ice makerDrop-in ice bin

Pizza oven

Pizza oven type

Kegerator

Trash pull-out

Storage doors

Single access doors, about 18" each.

Drawer banks (3-drawer stacks)

Appliances

Appliance brands / model numbers (optional)

Space check

90" of about 180" usable cabinet length

Step 7 of 9

Extras & utilities

Pergola or shade structure over the kitchen

Configure it in detail with the Pergola Builder and mention it in your notes.

Lighting (under-counter / task LED)

Outlets / GFCI prep

MS Metals provides openings in the frame for outlets; wiring and connections are by a licensed electrician, and we can help coordinate with them.

Gas

MS Metals builds a vented tank bay and gas-line access into the frame. Gas lines and connections are by a licensed gas contractor; we can help coordinate with them.

Water supply & drain for the sink

Step 8 of 9

Site & contact

Installation address / city

Property type

ResidentialCommercial / hospitality

Installation surface

Scope

Shop drawings + fabrication + installationShop drawings + fabrication + deliveryFabrication only (pickup)

Desired timeline

Site photos, plans or inspiration (optional)

auto_awesomeSend photos of the space, a sketch or inspiration images and we'll build the frame to your specs.

Images or PDF. Appliance spec sheets help us size the cut-outs.

Full name *

Phone

Email *

Notes

Step 9 of 9

Review & submit

Check your spec. You can go back to any step.

Live sketchUpdates as you choose